Stress changes of lateral collateral ligament at different knee flexion with or without displaced mo

来源 :中华创伤杂志(英文版) | 被引量 : 0次 | 上传用户:guoaiet
下载到本地 , 更方便阅读
声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架
论文部分内容阅读
Objective: To create a 3-dimensional finite element model of knee ligaments and to analyse the stress changes of lateral collateral ligament (LCL) with or without displaced movements at different knee flexion conditions.Methods: A four-major-ligament contained knee specimen from an adult died of skull injury was prepared for CT scanning with the detectable ligament insertion footprints,locations and orientations precisely marked in advance. The CT scanning images were converted to a 3-dimensional model of the knee with the 3-dimensional reconstruction technique and transformed into finite element model by the software of ANSYS. The model was validated using experimental and numerical results obtained by other scientists.The natural stress changes of LCL at five different knee flexion angles (0°, 30°, 60°, 90°, 120°) and under various motions of anterior-posterior tibial translation, tibial varus rotation and intal-extal tibial rotation were measured.Results: The maximum stress reached to 87%-113%versus natural stress in varus motion at early 30° of knee flexions. The stress values were smaller than the peak value of natural stress at 0° (knee full extension) when knee bending was over 60° of flexion in anterior-posterior tibial translation and intal-extal rotation.Conclusion: LCL is vulnerable to varus motion in almost all knee bending positions and susceptible to anterlor-posterior tibial translation or intal-extal rotation at early 30° of knee flexions.
其他文献
Polychromatic reconstruction(PCR) is a novel nondestructive readout method that utilizes a spectrally broad light source for the probe beam. The stored image ca
采用CdTe/ZnS复合钝化技术对长波HgCdTe薄膜进行表面钝化,并对钝化膜生长工艺进行了改进.采用不同钝化工艺分别制备了MIS器件和二极管器件,并进行了SEM、C-V和I-V表征分析,研
分析了非均匀性产生的主要原因 ,基于性能价格比和实时快速的原则 ,采用一点和两点法对固体图像传感器的非均匀性进行了校正并讨论了系统的校正范围 ,给出了用于实时校正的硬
在空间目标探测中,由于远距离、小目标的特点,回波信号十分微弱,传统的激光雷达不能很好地探测如此微弱的信号。而且现在空间目标探测不仅需要距离信息,还希望获得目标的强度
四年之后,若节能降耗和污染物减排指标能成功实现的话,回顾“十一五”,我们会发现,2006年是一个历史转折点.rn
采购的新使命是从供应链中发现机遇,并将其转化为满足客户战略需要的盈利机会.rn如果你能想象得到,企业负责人发现自己很少注意的业务单元其实对公司利润贡献巨大时,该是如何
刘斌工学博士/教授rn大连海事大学世界经济研究所所长.任辽宁省政府经济改革研究会常务理会,辽宁省市场经济学会副会长.中国交通运输协会特邀专家、新华社特邀经济专家、辽宁
在纸机上有5个重要的部位影响扬克缸涂层的性能,它们是:喷涂棒、涂布设备、刮刀、扬克缸表面温度、压榨托辊与毛毯.通过优化这些部位,卫生纸生产商可以少花钱甚至不花钱就能
为了使空间目标激光雷达成像仿真尽量反应实际在轨探测状态,提出了一种适用于复杂空间目标的在轨激光雷达成像仿真流程,并强调了面积法在复杂目标成像可见判断方面的适用性。
Futura公司于2009年在法国尼斯世界卫生纸会议上推出了JOI万能压花机,由于它所承诺的简单、灵活和加工性能,引起卫生纸行业很大的兴趣.从证明其优点以来,在全球已经有11台JOI