【摘 要】
：
Bis[2-(3,4-epoxycyclohexyl)ethyl]octamethyltetrasiloxane is also called diepoxycyclohexylethyl octamethyltetrasiloxane. In the present paper, diepoxycyclohexylethyl octamethyltetrasiloxane was synthesized, and the synthesized product was characterized by
【机 构】
：
School of Materials Science and Engineering, Nanchang University, Nanchang 330031, China
【出 处】
：
武汉理工大学学报（材料科学版）（英文版）
论文部分内容阅读
Bis[2-(3,4-epoxycyclohexyl)ethyl]octamethyltetrasiloxane is also called diepoxycyclohexylethyl octamethyltetrasiloxane. In the present paper, diepoxycyclohexylethyl octamethyltetrasiloxane was synthesized, and the synthesized product was characterized by FTIR and 1HMR. The synthesized product was compounded with some acrylates and an expoxide as well as photoinitiators to obtain a 3D printing stereolithography resin (3DSLR111). The properties of 3DSLR111 and its UV-cured samples were investigated by some instruments and equipments. The experimental results show that the critical exposure (Ec) of 3DSLR111 is 10.1 mJ/cm2, its penetration depth (Dp) is 0.15 mm, and its viscosity at 30 ℃ is 319 mPa·s. Some samples were printed with 3DSLR111, and their linear shrinkage and warping factor were evaluated. The linear shrinkage and the curl distortion factor are less than 0.80％ and 7.30％, respectively, which indicates that the sample printed with 3DSLR111 has high accuracy, and that the synthesized diepoxycyclohexylethyl octamethyltetrasiloxane can be well applied to the preparation of the photosensitive resin for stereolithography 3D printing.
其他文献
V-Cr-Al-O nanospheres were successfully synthesized using V2O5, Al(OH)3, CrO3, and H2C2O4·H2O as the starting materials by a facile one-pot hydrothermal approach. Several techniques containing X-ray powder diffraction, hydrogen temperature programmed redu
Eu3+ ion doped cubic Na5Lu9F32 single crystals with high quality were synthesized by a modified Bridgman method by using a high 70-90 ℃/cm temperature gradient for cross solid-liquid interface.The optical spectroscopic investigations of the obtained singl
Five kinds of mortars with density grades of 500, 600, 700, 800, and 900 kg/m3 were prepared. Their thermal conductivity and compressive strength were measured, and the morphological changes before and after simulated tunnel fire were observed. To investi
Influence mechanism of sulfide ions (S2-) during manganese electrodeposition from sulphate electrolyte was investigated. Under the experimental conditions, S2- ion concentration and electrolyte pH represented significant multiple effects on the cathode cu
The viscoplasticity and compressive strength of cement with high erosion performance were studied. The influences of curing temperature and content of ground granulated blast furnace slag (GGBFS) on these performances of the medium heat cement (including
The scope of the present paper is to understand the effects of crystalline admixture on the self-healing capacity of the cementitious composites. Previous studies were examined and a conclusion was drawn to the effect that different additives to crystalli
The internal curing effect of superabsorbent polymer (SAP) on the properties of high performance concrete (HPC) under marine wetting and drying cycles (WD cycles) was investigated. Compressive strength, hydration and chloride migration were experimentally
The binder properties were determined in accordance with Chinese standard such as ductility test, which allowed to measure the distance in centimeters that a standard briquette of asphalt had been stretched before breaking. Then, penetration test was carr
An effect of heating and stirring in a facile wet chemical route to synthesize entangled nano-fibrous mesh of doped polyaniline (PANI) was reported. The structural, morphological, and optical properties of PANI nano-fibers were found to be dependent on sy
A dual-receptor targeting delivery system based on acid-cleavage hydrazone bond was developed in the study. The characters of CMCS-hyd-CUR-EGFR- mAb were identified. The in vitro release studies revealed that this drug delivery system was acid-sensitive,