Structural integrity and damage of ZrB2 ceramics after 4 MeV Au ions irradiation

来源 :材料科学技术(英文版) | 被引量 : 0次 | 上传用户:yanguoke
下载到本地 , 更方便阅读
声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架
论文部分内容阅读
Ultra-high temperature ceramics have been considered as good candidates for plasma facing materials due to their combination of high melting point,high strength and hardness,high thermal conductivity as well as good chemical inertness.In this study,zirconium diboride has been chosen to investigate its irradiation damage behavior.Irradiated by 4 MeV Au2+ with a total fluence of 2.5 × 1016 cm-2,zirconium diboride ceramic shows substantial resilience to irradiation-induced damage with its structural integrity well maintained but mild damage at lattice level.Grazing incident X-ray diffraction evidences no change of the hexagonal structure in the irradiated region but its lattice parameter a increased and c decreased,giving a volume shrinkage of ~0.46%.Density functional theory calculation shows that such lattice shrinkage corresponds to a non-stoichiometric compound as ZrB1.97.Electron energy-loss spectroscopy in a transmission electron microscope revealed an increase of valence electrons in zirconium,suggesting boron vacancies were indeed developed by the irradiation.Along the irradiation depth,long dislocations were observed inside top layer with a depth of~750 nm where the implanted Au ions reached the peak concentration.Underneath the top layer,a high density of Frank dislocations is formed by the cascade collision down to a depth of 1150nm.All the features show the potential of ZrB2 to be used as structural material in nuclear system.
其他文献
采用有限元辅助进行碳纤维扭转轴定刚度设计,通过碳纤维缠绕成型工艺制备碳纤维扭转轴,并进行扭转刚度测试验证.结果 表明,有限元计算得到碳纤维扭转轴扭转刚度为31.08 kN·m
针对目前模压、缠绕等工艺成型烧蚀防热复合材料易造成层间结合差、脱粘、抗烧蚀性能差、易剥蚀等问题,提出了一种新型压力辅助RTM工艺,并对其进行了树脂充模流动模拟,制备了烧蚀防热复合材料,测试了材料的孔隙率、力学性能、烧蚀性能。结果表明:压力辅助RTM工艺具有可行性与优越性,复合材料孔隙率4.64%,层间剪切强度39.3 MPa,线烧蚀率0.017 mm/s,质量烧蚀率0.0538 g/s。说明压力辅助RTM工艺适合成型烧蚀防热复合材料。
梳理和分析了水下阀门的设计规范、选材原则、设计要求、性能考核要求等,为水下阀门的工程化研制提供技术支持和研究依据。
金属材料疲劳裂纹扩展速率是对金属材料及其零构件含有裂纹体后安全服役评价及疲劳寿命评估的一项重要力学性能指标。基于金属材料疲劳裂纹扩展过程的不同阶段、闭合效应、应力比对疲劳裂纹扩展速率的影响等多个方面,对几种常见金属材料疲劳裂纹扩展速率模型的应用特点进行了对比分析,为安全设计及寿命评估时不同模型的选择应用提供参考。
Ultrafine-grained alloys fabricated by severe plastic deformation (SPD) have high strength but often poor uniform ductility.SPD via high-ratio differential spee
The widespread use of water-repellent superhydrophobic surfaces is limited by the inherent fragility of their micro-and nanoscale roughness,which is prone to da
Super-fine L10-FePt nanoparticles (NPs) with high ordering degree were successfully prepared by a modified two-step sintering method,which includes low-temperat
Porous g-C3N4 nanosheets (PCN) were prepared by the nickel-assisted one-step thermal polymerization method.Hydrogen (H2) which was produced by the reaction betw
介绍了环形对苯二甲酸丁二醇酯(CBT)的性能特点及其应用,综述了纤维增强CBT树脂基复合材料的国内外研究现状,包括制备工艺、力学性能以及应用等,并对其在复合材料领域的发展
Electrolyte formulation with high stability towards both Li metal anode and high-voltage cathode is considered as one of key points for the high-energy density