2. 您的位置
3. 首页
4. 期刊论文
5. Texture evolution during semicontinuous equal-channel angular extrusion process of interstitial-free

Texture evolution during semicontinuous equal-channel angular extrusion process of interstitial-free

来源 :宝钢技术研究：英文版 | 被引量 : 0次 | 上传用户：zhaogaoheng123

【摘 要】

：

Semicontinuous equal-channel angular extrusion( SC-ECAE) is a novel severe plastic deformation technique that has been developed to produce ultrafine-grain stee

【作 者】

：

YAN Bo JIAO Sihai ZHANG Dianhu 

【机 构】

：

StateKeyLaboratoryofRollingandAutomation,ResearchInstitute

【出 处】

：

宝钢技术研究：英文版

【发表日期】

：

2015年4期

【关键词】

：

等通道转角挤压 IF钢 半连续 挤压过程 织构 场发射扫描电子显微镜 电子背散射衍射 小角度晶界 severe plastic deformation semi 

下载到本地 , 更方便阅读

下载此文 赞助VIP

声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架

论文部分内容阅读

Semicontinuous equal-channel angular extrusion( SC-ECAE) is a novel severe plastic deformation technique that has been developed to produce ultrafine-grain steels. Instead of external forces being exerted on specimens in the conventional ECAE,driving forc

其他文献

High-temperature oxidation behavior of heat resistant stainless steel 1.4828

The kinetic curves of the high-temperature oxidation of austenitic heat resistant stainless steel 1.4828 at1050℃ were measured using a weighing method.It is sh

期刊

高温氧化行为耐热不锈钢X射线衍射分析扫描电子显微镜动力学曲线不锈钢管表面形态氧化物1. 4828 heat resistant stainl

The effect of different cooling and tempering conditions on the strength and toughness of SA533B ste

The microstructure and mechanical properties of SA533B low-alloy steel were investigated under different cooling and tempering conditions. Steel plates cooled a

期刊

回火马氏体冷却速度低合金钢韧性强度脆性转变温度显微组织贝氏体钢SA533B steel cooling rate tempering st

一种应用于DC-DC的新型基准源电路设计

主要介绍了一种新型CMOS基准源电路的设计方法,由NMOS管阈值电压的温度系数及NMOS管迁移率温度指数形成温度补偿,同时产生低温度系数的基准电压和基准电流.此基准源电路已经

期刊

DC-DC转换器基准电压基准电流阈值电压迁移率DC-DC converters voltage reference current referen

Investigation of a novel spot defect on a hot dip galvanized high-silicon AHSS sheet

Improving the galvanizability of high silicon advanced high strength steels(AHSS) is a practical technical challenge. In this study,spot defects on an industria

期刊

热镀锌钢板缺陷调查高硅金属间化合物扫描电子显微镜氧化硅薄膜能量色散谱仪光学显微镜high Si containing AHSS galvan

Experimental study on the causes of cracking of high-strength steel during bending

This paper studies the chemical composition,tensile properties,inclusions,metallogrophic structure,and other such parameters to identify the causes of cracking

期刊

高强度钢板弯曲过程原因实验开裂横向裂缝表面裂缝化学成分bending cracking high-strength steel incl

一维有限孔径时谐辐射的一种解析分析

给出了计算一维有限孔径时谐辐射的一种简单的解析描述。根据线源叠加理论，在Fresnel近似条件下推得一计算辐射场的积分公式。通过用矩形函数对孔径上场分布函数的加权，并利用

期刊

孔径辐射高斯展开Kirchhoff积分aperture radiation gaussian expansion kirchhoff integrat

Thermo-Calc calculations and studies of the heating process of Fe83Si4B13 alloy

The microstructural changes of Fe83Si4B13 amorphous mother alloy during the heating process were investigated by Laser Scanning Confocal Microscopy（ LSCM）,and the

期刊

加热过程计算值母合金激光扫描共聚焦显微镜差示扫描量热法LSCMDSC微观结构Fe-Si-B ternary alloy heating pro

Investigation of the mechanical performance of Al-coated DI steel sheets prepared by DC magnetron sp

Aluminum films coated on DI steel sheets were prepared by direct current(DC)magnetron sputtering. The influence of the deposition conditions and film thickness

期刊

涂层钢板磁控溅射溅射制备铝薄膜机械性能DIDC薄膜厚度Al magnetron sputtering packing materials

基于FPGA指纹识别系统的设计与实现

提出了一种基于FPGA的指纹识别系统的设计方案。论文详细介绍了指纹识别系统的基本原理、系统的总体框架结构、系统硬件结构设计和软件编程设计，以及系统的优化设计方案。该指

期刊

指纹识别NIOSⅡFPGAfingerprint identification Nios FPGA

Reasons and countermeasures for ＂marking problem＂ during the production of double-walled copper-braz

This study explores the reasons underlying the frequent appearance of "marking problem "during the production of double-walled copper-brazed steel tubes. To thi

期刊

钢管生产铜钎焊标记双壁原因生产过程化学成分力学性能double-walled copper-brazed marking problem