“七五”时期保山地区城镇集体经济的设想

来源 :经济问题探索 | 被引量 : 0次 | 上传用户:m6300
下载到本地 , 更方便阅读
声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架
论文部分内容阅读
“六五”时期的五年是保山地区城镇集体工业企业贯彻落实“改革、开放、搞活”的各项经济政策,在休养生息中前进的五年,过去五年中新情况新问题不断出现,企业怎样才能生存发展的问题已逐步为广大干部职工认识和掌握。过去的五年不但为我们打下了本世纪末翻两番的初步基础,而且为争取“七五”计划的实现,积累了重要的经验教训。因此,认真总结“六五”经验,对于开创“七五”时期城镇集体经济的新局面是大有裨益的。“六五”时期的工作回顾及主要经验“六五”期间,保山地区城镇集体工业经济取得了较好的成绩,生产不仅比“五五”时期有提高,而且五年中年年有发展,收到了较好的经济效益和社会效益。1.工业总产值较之“五五”期间有较大增长。“六五”期间共完成工业总产值15.972万元,比“五五”期间增长30%。 Five years during the “Sixth Five-Year Plan” period are the five years in which collective industrial enterprises in cities and towns in Baoshan District have implemented the economic policies of “reform, opening up and invigorating” and have progressed in recuperation. In the past five years, new problems and new problems continued to emerge. Enterprises The question of how to survive and develop has gradually become known and mastered by the vast numbers of cadres and workers. The past five years not only laid the initial foundation for us to quadruple the end of this century, but also accumulated important lessons and lessons for the realization of the 7th Five-Year Plan. Therefore, earnestly concluding the “Sixth Five-Year Plan” experience is of great help to ushering in the new situation of urban collective economy during the “7th Five-Year Plan”. Work Review and Main Experiences in the Period of the Sixth Five-Year Plan During the period of the Sixth Five-Year Plan, the collective industrial economy in Baoshan Municipality achieved relatively good results. The production not only increased compared with the “Five Five” period, but also developed in the middle five years. Received a better economic and social benefits. 1. The industrial output value has a larger growth than the “five five” period. During the “Sixth Five-Year Plan” period, the total industrial output value was 159,720 yuan, an increase of 30% over the “Five-Five” period.
其他文献
在粒子源问题中,质量为 m、带电量为 q 的粒子,以相同大小、不同方向的速度 v 垂直射入磁场,在磁感应强度为 B 的匀强磁场中做圆周运动的问题,解决起来比较复杂,其关键是建
一、问题的提出电子工业部某厂生产密封继电器,年产一百多万个。为了提高在各种环境下工作的可靠性,提高继电器的工作寿命,继电器内部需充以惰性气体,所以要求继电器外壳有
一、前言对大截面钢芯铝绞线进行爆炸压接时,时有出现压接管内的外露钢芯被烧伤以致断裂的问题,严重影响接头的强度.为了更有效地防止钢芯损伤事故,必须充分深入研究钢芯损
1.跑鱼记2010年7月16日,我得到消息,彰武水库小庙附近最近出的鲫鱼比较大,大部分都在100克以上,还有人不时钓到六七两的大鲫鱼,钓饵基本上都是蚯蚓。17日上午我好好准备了一
加工内球面一般没有专用机床,大都是靠自行设计制造内球面镗杆在镗床或车床上加工。我厂在T611镗床上加工φ650~φ750的两种球面轴承座时,利用了一般的蜗轮蜗杆进刀装置,仅在
文章从以下几个方面论述了磨床技术的进展。 一、更换砂轮装置 过去几年中,磨床结构最值得注意的变化是自动更换砂轮装置的出现。 目前,万能外圆磨床上,通常都有一个转塔式的
本文通过对国外水中兵器的材料剖析,综述了国外水中兵器用材的特点,介绍了我国水中兵器材料的选用情况,并提出在材料选用方面的可以借鉴之处。 Based on the material analy
我厂生产的拖拉机零件中,有几种零件内孔均需加工内卡簧槽。我们在CB3463转塔式多刀半自动车床或自动生产线上进行加工,由于车削完毕后刀架退刀速度慢,而纵向溜板返回较快,
本赛季被彻底解放的他已经在10场比赛中打进11球,相比上赛季在莫里尼奥手下的平淡,也难怪“猎豹”会“口无遮拦”地说:“作为一个前锋,我喜欢贝尼特斯这样的教练,他能让我更
日本三井工作所总厂有一电机铁芯冲压车间,其电机铁芯片的冲压、计数、叠压工序均在模具中自动完成。叠压成整体的转子和定子,分别从模具中被推出。这种模具是在电机铁芯级