【摘 要】
：
Within this work, we present a system for the measurement of the three-dimensional (3D) trajectories of spatters and entrained particles during laser powder bed fusion (L-PBF) of metals. It is comprised of two ultrahigh-speed cameras and a reconstruction
【机 构】
：
InstituteofPhotonicTechnologies,Friedrich-Alexander-UniversitatErlangen-Nürnberg,Konrad-Zuse-Str.3/5
【出 处】
：
InternationalJournalofExtremeManufacturing
论文部分内容阅读
Within this work, we present a system for the measurement of the three-dimensional (3D) trajectories of spatters and entrained particles during laser powder bed fusion (L-PBF) of metals. It is comprised of two ultrahigh-speed cameras and a reconstruction task specific processing reconstruction algorithm. The system enables an automated determination of 3D measures from the trajectories of a large number of tracked particles. Ambiguity evolving from an underdetermined geometrical situation induced by a two-camera setup is resolved within the tracking using a priori knowledge of L-PBF of metals. All processing steps were optimized to run on a graphics processing unit to allow the processing of large amounts of data within an appropriate time frame. The overall approach was validated by a comparison of the measurement results to synthetic images with a known 3D ground truth.
其他文献
In order to increase the anti-counterfeiting performance of optically variable devices, the innovative interference security image structures based on metamerism have been developed. In this letter, we show a pair of all-dielectric metameric filters offer
A band-stop angular filter (BSF) based on hump volume Bragg gratings (HVBGs) is proposed. Band-stop filtering in a two-stage amplifier laser system is discussed and simulated. Simulation results show that small-scale self-focusing effects in the laser sys
通过溶剂热法合成了石墨烯-硫化镉(G-CdS)复合材料。利用X 射线衍射仪、透射电子显微镜和紫外可见光谱仪对G-CdS复合材料的结构、尺寸、形貌和吸收特性等进行了表征，结果表明硫化镉量子点的平均尺寸为7 nm，且较为均匀地附着在石墨烯上。利用单光束Z-扫描技术研究了G-CdS复合材料在波长为532 nm、脉冲宽度为30 ps激光作用下的三阶非线性光学特性，结果表明G-CdS复合材料具有正的非线性折射率和饱和吸收特性，其三阶非线性极化率为4.36×10-12 esu，非线性吸收系数为-
利用CH3Cl、CH3F、CH3F、CH3CHF2、CH2=CF2与C2H3Cl分子在9.4、10.4微米频带的各种谱线上的斯塔克效应，已观察到CO2激光器的高效率激励Q调制作用。用脉沖和正弦电场施加到腔内调制器上，都观察到这种效应。
基于传统光干涉甲烷检测仪,可以根据干涉条纹的位移量判断甲烷气体的浓度是否存在危险,而快速、准确地提取干涉条纹的中心线便可降低测量误差提高准确度。在考虑到光源、检测环境等因素的基础上,通过现场可编程门阵列(Field-Programmable Gate Array,FPGA)对图像进行预处理。首先对图像进行灰度化转换,并选用中值滤波对其进行降噪处理,然后进行二值化处理,最后选用骨架细化法提取条纹中心
本文介绍一种新颖的TEACO2激光器.它是采用共腔式结构,在一次激励下可获得脉冲时间间隔τ从0～15μs的连续可变的双脉冲、而无需气体循环的系统.本文还给出了该器件的结构、控制电路的设计特点,实验结果及结论.
在蓝绿激光对潜通信及对潜探测应用中, 激光分别通过大气、气-海界面以及海水信道传输。由于海面上方覆盖海雾、风速引起海面粗糙度变化以及覆盖泡沫、海水信道中存在悬浮粒子等多种因素的影响, 蓝绿激光传输信道呈现复杂特征。基于米散射理论、粗糙面散射理论及辐射传输理论, 针对上述复杂海况开展海雾大气、泡沫覆盖风驱粗糙海面及考虑浮游植物分布的海水信道的激光传输特性研究, 并详细讨论了风速、海雾能见度及浮游植物分布对激光功率的衰减作用。结果表明：海雾、粗糙海面泡沫和海水信道中浮游植物对传输激光功率共同起作用, 其中海水
作为一类新型薄膜太阳能电池, 近年来钙钛矿太阳电池的发展十分迅速, 其效率已接近商业化硅基太阳能电池, 但是钙钛矿薄膜在空气中稳定性较差, 严重限制了其进一步的商业化应用。本研究通过在钙钛矿薄膜中添加聚4-乙烯吡啶(PVP)来增强钙钛矿薄膜在空气中的稳定性。通过形貌、结构及性能测试, 发现相比于未添加PVP的钙钛矿薄膜, 添加PVP的钙钛矿薄膜形貌更均匀致密。添加0.4wt% PVP将钙钛矿太阳电池的光电效率从6.09%提升到13.07%, 而且, 存放在相对湿度超过50%的空气中, 其电池效率衰减为一半