【摘 要】
：
The influence of simple thermomechanical processing such as hot deformation and heat treatment on the microstructure and hardness of an Al0.3CoCrFeNi high-entropy alloy has been investigated.Results show that the relatively high deformation temperature ca
【机 构】
：
State Key Laboratory of Solidification Processing,Northwestern Polytechnical University,Xi’an 710072
论文部分内容阅读
The influence of simple thermomechanical processing such as hot deformation and heat treatment on the microstructure and hardness of an Al0.3CoCrFeNi high-entropy alloy has been investigated.Results show that the relatively high deformation temperature can induce discontinuous dynamic recrystallization with fine grains initially nucleating at the elongated grain boundaries.The transition from partial recrystallization to fully recrystallization,as well as the precipitation behavior after annealing,has been described in detail.Both bcc precipitation and completely recrystallized grains can be observed after annealing at 1000 ℃.Based on detailed microstructure analysis,the decrease in hardness value is shown to be related to both dynamic recrystallization and dynamic recovery which lead to softening.
其他文献
H13是一种典型的空冷硬化热作模具钢,抗热裂能力良好,适合工作温度低于600 ℃.其工艺性能优良,是目前国内外应用最广泛的热作模具钢种之一[1-3].通常用于制造铝铸件用的热挤压模、压铸模、热锻模的热冲孔模具、热切边模等,还广泛应用于铜及其合金的压铸模具[4-5].H13钢中合金元素含量高达9％,奥氏体在高温变形过程所发生的组织结构变化复杂,通过研究H13钢高温变形行为,确定合理的轧制参数,保证工业化生产顺利进行.
在连续热镀锌生产线中,清洗段需要热脱盐水用于清洗带钢表面的油污和铁粉[1].热脱盐水采用与余热回收及蒸汽加热的过热水循环系统换热制取.马钢(合肥)板材有限责任公司连续热镀锌线过热水循环系统采用节能优化技术,根据流体力学与热交换原理,通过对系统中水泵、阀门与管网、换热器、补水罐等单元进行优化控制,将闭路循环的过热水终端的温度、流量和工艺参数严格控制在设定的区间内,达到吸收退火炉排放的热量并加热清洗脱 盐水的目的.
我国是钛资源大国,约占世界总储量的三分之一,其中攀枝花地区钛资源储量约占国内总量的90％[1-2],其中超过一半以钒钛磁铁矿形式存在,且钙、镁、硅、铝等杂质含量高,导致钒钛磁铁矿精矿经还原-熔分工艺得到的含钛电炉渣中TiO2质量分数仅22％左右,因此难以用硫酸酸解和浸出其中的钛[3].为了提高钛的提取率需要用更多的硫酸,以及更苛刻的酸解条件进行钛的提取,导致得到的钛液中酸度值和硅、钙等杂质含量高[4].
在连续热镀锌带钢生产中,退火炉作为整条机组产线的核心,该岗位的操作工常被定为“关键岗”,由此说明连续退火炉在镀锌机组中的地位是不可替代的.由于连续热镀锌机组设备构成复杂,产品缺陷也多种多样,其中处理起来最为困难的当属发生在炉辊结瘤而产生的硌印或划伤.由于作业环境恶劣,且不可直观观察,因而导致处理过程异常困难,对产品质量及产线的连续性运行影响很大,所以工艺执行及退火炉的日常维护就显得尤为重要.本文着重介绍设备维护对设备寿命和产品质量的 影响.
溅射靶材是半导体芯片加工中的配线材料,由于集成电路设计复杂,金属配线对导电性能要求很高[1-2],因此对真空环境下的溅射金属的纯度要求非常严苛,要求纯度达到 99.999％[3-4],本研究选用5NAl作为溅射材料.rn靶材的基座背板主要起到固定和托底的作用,同时在溅射过程中起到迅速冷却的作用[5-6],因此需要选用一种具有一定强度的金属起固定作用,并在长时间的高压下不易变形,易散热的材料作为背板金属[7-8],同时需要和铝具备较好的焊接性,本研究选用TU1-Cu作为背板材料.
在炼钢生产中为保证板坯产品质量避免因钢水的含氧量高而出现皮下气泡等缺陷[1-2],通常需要加入铝锭、硅铝钡钙等强脱氧剂来控制钢水的脱氧深度[3],不可避免地会出现Als及Al2O3等高熔点夹杂物浇注进入中包以后附着在塞棒、上水口以及下水口等位置.此类夹杂物附着以后难以再被冲刷进入钢水,当夹杂物聚集达到一定程度以后,即造成浇铸过程中的絮流现象[4].絮流产生以后控流不稳,浇铸液面剧烈波动,极易造成卷渣,严重时甚至导致漏钢.受液面波动影响,连铸拉速短时间内大幅下降,造成铸坯出现接头及表面纵裂等缺陷,严重影响连
A carbon-containing CoCrFeNi high entropy alloy (HEA) with heterogeneous structures was obtained through thermome-chanical treatments,which induced concurrent recrystallization and carbide precipitation in the alloy.A combination of high yield strength (5
To shed light into the application potential of high-entropy alloys as “interlayer” materials for Al-steel solid-state joining,we investigated the nature of the CoCrFeMnNi/Fe and CoCrFeMnNi/Al solid/solid interfaces,focusing on the bonding behav-ior and p
Entropy-stabilized multi-component alloys have been considered to be prospective structural materials attributing to their impressive mechanical and functional properties.The local chemical complexions,microstates and configurational trans-formations are
Mechanical properties of high-entropy alloys (HEAs) with the face-centered cubic (fcc) structure strongly depend on their initial grain orientations.However,the orientation-dependent mechanical responses and the underlying plastic flow mecha-nisms of such