Preparation and Catalytic Performance of Microporous Polymer/Au Nanoparticles Composite Microspheres

来源 :武汉理工大学学报(材料科学版)(英文版) | 被引量 : 0次 | 上传用户:myplucky
下载到本地 , 更方便阅读
声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架
论文部分内容阅读
Polystyrene crosslinked microspheres were prepared by soap-free emulsion polymerization using styrene (St) and divinylbenzene (DVB) as monomers; then, the microporous structure was knitted by the Friedel-Crafts alkylation reaction, and the Au nanoparticles (AuNPs) were loaded into the pores through thermal reduction, to obtain AuNPs/ hyper-crosslinked microporous polymer composite microspheres. SEM and particle-size test results show that the microspheres show good monodispersity. The micropore analysis indicates that the specific surface area and the pore volume of the microporous polymer microspheres decrease with increasing DVB content, and when the DVB content is 0.1%, the specific surface area reaches a maximum of 1174.6 m2/g. After loading AuNPs, the specific surface area and the amount of micropores of the composite microspheres decrease obviously. The results of XRD and XPS analyses suggest that HAuCl4 is reduced to AuNPs. The composite microspheres show a good catalytic performance for the reduction catalyst of 4-nitrophenol.
其他文献
Catalyst enhanced chemical vapor deposition of nickel film on high Tg polymers such as teflon (PTFE), polyimide(PI), and polysulfone(PS) was investigated by hot wall and cold wall CVD, in which Ni(dmg)2, Ni(acac)2, Ni(hfac)2, Ni(TMHD)2, and Ni(cp)2 are us
Nano-ZrO2 and PEEK particles were synergistically filled in unfilled PTFE to improve the wear resistance and maintain a relatively low friction coefficient, and the materials were studied using a reciprocating sliding friction and wear tester. In the fric
A post-treatment of hydrothermal process was conducted to evaluate its effects on the material characteristics and mechanical properties of plasma-sprayed pure HA and HA/20% YSZ coatings. Surface morphology and microstructural changes, relative element co
The polymeric admixture,the sodium-carboxymethylcellulose (CMC)/poly sodium p-styrene sulfonate (PSS) / poly vinyl acetate (PVAc) was synthesized and applied in cement mortars.The polymer was tested by FTIR and SEM,and the results indicate that the ideal
The nucleation process of graphene films prepared by pulsed laser deposition has been investigated in detail. It is found that graphene nucleates at the steps on the substrate surface firstly, from aggregation of nuclei into particles. High pulsed laser e
In order to explore the effect of high-temperature annealing on the mechanical performances and microstructures of different oxygen SiC fibers, two types of silicon carbide (SiC) -based fibers, specified as XD-SiC fibers (low oxygen) and Nicalon-201 fiber
A recrystallization and partial melting (RAP) process was introduced to prepare the semi-solid 7075 aluminum alloy used for thixoforming. In order to obtain an ideal semi-solid microstructure, a series of extrusion experiments were conducted to comparativ
A plasma cladding experiment was carried out to investigate the characteristics(surface hardness, microstructure, friction, wear properties from different substrates to the cladding layer and the bond strength) of plasma cladding Fe-Cr-Nb-Si-Mo alloy clad
The 0.6mol% CuO-doping 0.996(0.95Na0.5K0.5NbO3-0.05LiSbO3)-0.004FeBiO3 (KNN-LSBF-CuO) piezoelectric ceramics were synthesized by a solid-state reaction technique, and the structure and piezoelectric properties dependence of sintering time in KNN-LS-BF-CuO
Low-cost porous calcined dolomite microspheres were prepared by simple spray drying and subsequent calcination. Effects of calcination temperature on phase evolution and adsorption properties of MB were investigated systematically. Results showed that mic