2. 您的位置
3. 首页
4. 期刊论文
5. Inhomogeneity of microstructure and mechanical properties of a 500 mm diameter heavy section semi-co

Inhomogeneity of microstructure and mechanical properties of a 500 mm diameter heavy section semi-co

来源 :中国铸造：英文版 | 被引量 : 0次 | 上传用户：baofeifly

【摘 要】

：

For the large magnesium alloy ingot, there is a considerable difference in cooling rate of different parts in the ingot, which leads to non-uniform distribution

【作 者】

：

PengJian TaoJianquan TongXiaos 

【机 构】

：

CollegeofMaterialsScienceandEngineering,No.59InstituteofChinaOrdnancehldustry

【出 处】

：

中国铸造：英文版

【发表日期】

：

2014年1期

【基金项目】

：

This research was financially supported by the National Key Technology R＆D Program （No. 2012BAF09B04）, the International Technical Cooperation Project （No. 2011DFR50950） of the Ministry of Science and

下载到本地 , 更方便阅读

下载此文 赞助VIP

声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架

论文部分内容阅读

For the large magnesium alloy ingot, there is a considerable difference in cooling rate of different parts in the ingot, which leads to non-uniform distribution of the secondary phases, solute segregation and tensile properties. In the present research, a

其他文献

Effect of nodule count and austempering heat treatment on segregation behavior of alloying elements

The equilibrium partition ratio, k, has been measured for Mn, Mo, Si, Ni and Cu in a ductile iron with composition(wt.%): 3.45 C, 0.25 Mn, 0.25 Mo, 2.45 Si, 0.5

期刊

Research progress on microstructure evolution of semi-solid aluminum alloys in ultrasonic field and

The effects of ultrasonic vibration(UV)treatment on microstructure of semi-solid aluminum alloys and the application of UV in rheocasting process are reviewed.G

期刊

Huazhong University of Science and Technology

Since 1952,Huazhong University of Science and Technology(HUST)was founded,or even further back,the German doctor Erich Paulun founded Tongji Medical University(

期刊

HuazhongUNIVERSITYofSCIENCEandTECHNOLOGY

Improvement in collapsibility of ZrO2 ceramic mould for investment casting of TiAl alloys

投资扔广泛地在与精确性，通用性和正直的关键好处生产 TiAl 部件作为最好的选择被认出了。为投资扔的陶器的模子的 collapsibility 由于 TiAl 在房间温度的内在的易碎物在 TiA

期刊

COLLAPSIBILITY改进ZrO2陶器的模子TiAl合金扔的投资collapsibility improvement ZrO2 cerami

Effect of Mn on hardenability of 25CrMo axle steel by an improved end-quench test

With the sixth large-scale railway speed-up,the quality of the axles is essential to the safety of the locomotive.According to the high-speed axle technical sta

期刊

金属材料不锈钢钢材组织结构铸铁25CrMo steel end-quench test hardenability microstructure Mn

Evolution of rheocast microstructure of AZ31 alloy in semisolid state

Semisolid rheoforming(SSR)is a promising technology for the production of Mg wrought alloy in foundry settings.In order to realize SSR,it is necessary to charac

期刊

金属材料有色金属材料有色轻金属材料铝材料rheocast microstructure evolution mechanism AZ31 alloy q

Dependency of microstructure and microhardness on withdrawal rate of Ti-43Al-2Cr-2Nb alloy prepared

The intermetallic Ti-43Al-2Cr-2Nb（at.%） alloy was directionally solidified in an electromagnetic cold crucible with different withdrawal rates（V） ranging from 0.2 t

期刊

TiAl-basedalloysdirectionalsolidificationMICROSTRUCTUREMICROHARDNESSmicroh

Compressive properties of aluminum foams by gas injection method

The compressive properties of aluminum foams by gas injection method are investigated under both quasi-static and dynamic compressive loads in this paper. The e

期刊

FOUNDRY

期刊

中国机械工程学会铸造分会有色金属铸件铸造技术科技成果管理经验国内外外信息铸铁

Abnormal mechanical property evolution induced by heat treatment for a semi-solid forming hypereutec

In the present study, Al-5.5Fe-4Cu-2Zn-0.4Mg-0.5Mn al oy samples were prepared by electromagnetic stirring and semi-solid forming processing, and then the effec

期刊