Analysis of Air Voids Evolution in Cement Pastes Admixed with Non-ionic Cellulose Ethers

来源 :武汉理工大学学报(材料科学版)(英文版) | 被引量 : 0次 | 上传用户:qzyss
下载到本地 , 更方便阅读
声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架
论文部分内容阅读
Four cellulose ethers (CEs) were compared for their effects on the pore structure of cement paste using mercury intrusion porosimetry. The experimental results show that the total pore volume and porosity of cement pastes containing the four cellulose ethers are significantly higher than that of the pure cement pastes and the total pore volume and porosity of cement pastes containing HEC (hydroxyethyl cellulose ether) or low viscosity cellulose ethers are low in four CEs. By changing the surface tension and viscosity of liquid phase and the strengthening of liquid film between air voids in cement pastes, CEs affect the formation, diameter evolution and upward movement of air voids and the pore structure of hardening cement paste. For the four CEs, the pore volume of cement pastes containing HEC or low viscosity cellulose ethers is higher with the diameter of 30-70 nm while lower with the diameter larger than 70 nm. CEs affect the pore structure of cement paste mainly through their effects on the evolvement of the small air voids into bigger ones when the pore diameter is below 70 nm and their effects on the entrainment and stabilization of air voids when the pore diameter is above 70 nm.
其他文献
To develop an efficient and bio-compatible way to improve the thermal and mechanical properties of addition type liquid silicone rubber (LSR),a series of modified LSR samples were prepared by introducing octavinyl-polyhedral oligosilsesquioxanes (VPOSS) a
To efficiently utilize the kaolin, an economical way of preparing cordierite ceramic with high performance for electric heater supports was put forward. In this study, sintering process, phase transformation, microstructure evolutions were systematically
A new type of capric acid (CA)-acid expanded vermiculite (AEV) composite phase change material (PCM) with improved adsorption ability and interface adhesive strength was developed. Through the analysis of non-isothermal phase transition kinetics, modified
The isothermal absorption properties and kinetic model of Cr (Ⅵ) and Cr (Ⅲ) onto ettringite were investigated using the batch adsorption method. IR analysis was used to study the difference and mechanism of the adsorption of chromium ions with different v
The mechanical and thermal properties of steel reinforced concrete columns with CFRP reinforcement were examined after exposure to a high temperature of 500℃. The concrete made with normal and recycled coarse aggregate (RCA) was fabricated and three diffe
Due to the intrinsic nature of a heterogeneous and anisotropic microstructure of cement based materials and the small indentation size, the measured microhardness values are subject to considerable variability. This work presents an in-depth assessment of
Cement raw meal with MSS and different heavy metals was blended to examine the fixation ratios, chemical species, and cement crystalline phases in clinkers. The results showed that blending MSS could decrease the fixation ratio of Cr, Ni, Cu, and Zn in th
Hydration heat behavior and kinetics of blended cement containing up to 20% MSWI fly ash were investigated based on its hydration heat evolution rate measured by isothermal calorimeter. Kinetics parameters, N and K, and hydration degree, Ca(OH)2 content,
Pure copper plates were coated by Ni-TiC dipulse current plating method.The effects of adding different concentration(ranging from 0.5 g/L to 3.0 g/L) of attapulgite nano particles to the plating bath on the surface morphology,wear resistance,and oxidatio
The elastic-plastic transition regime and brittle-ductile transition regime in scratch process for optical glass BK7 were analyzed based on the Hertzian equation and the stress ratio theory which was proposed by Wei. The interacting scratch process for op