【摘 要】
：
为了研究珠江河口营养物质循环和溶解氧,建立了一个生态型水质模式.在该水质模式中营养物质以溶解无机态、碎屑有机物质、底栖物质、浮游植物和浮游动物等5种形态出现,而每种
【机 构】
：
香港科技大学海岸与大气研究中心,香港科技大学海岸与大气研究中心,国家海洋局海洋动力过程与卫星海洋学重点实验室 香港九龙,国家海洋局 海洋动力过程与卫星海洋学重点实验室,浙江 杭州 310012,国家海
论文部分内容阅读
为了研究珠江河口营养物质循环和溶解氧,建立了一个生态型水质模式.在该水质模式中营养物质以溶解无机态、碎屑有机物质、底栖物质、浮游植物和浮游动物等5种形态出现,而每种形态均分氮和磷两种形式.水质模式采用三维形式,并与斜压水动力和泥沙模式联立运行.
In order to study the nutrient cycling and dissolved oxygen in the Pearl River estuary, an ecological water quality model was established, in which nutrients were found in five different forms: dissolved inorganic, organic debris, phytoplankton, zooplankton and zooplankton , And each form is divided into two forms of nitrogen and phosphorus.The water quality model using three-dimensional form, and with baroclinic hydrodynamic and sediment model run together.
其他文献
为了检测牛GDF-9基因mRNA在怀孕期牛生殖系统的表达情况,为GDF-9基因在雌性动物繁殖上的研究提供一定的理论依据.本试验根据GenBank中报道的牛GDF-9基因序列设计引物,从牛卵
Virtual manufacturing is fast becoming an affordable technology with wide-ranging applications in mod ern manufacturing. Its advantages over existing technology
YSZ (yttria stabilized zirconia) electrolyte properties made from different sizes of nano powders were investigated. As a result, the sample marked KD with the
This paper used Baumel Jr. and Seegers approach estimating fatigue parameters of 48MnV with 3Cr13coatings. The fatigue life of the crankshaft of a six-cylinder
A new discretization scheme is proposed for the design of a fractional order PID controller. In the design of a fractional order controller the interest is main
Based on principal component analysis, a multiple neural network was proposed. The principal component analysis was firstly used to reorganize the input variabl
A simple and easily operated technique was developed to fabricate GaN films. GaN films possessing hexagonal wurtzite structure were fabricated on Si(111) substr
β-葡聚糖在蜡质淀粉型大麦Candle麸皮中的含量(11.62%,w/w,干基)、提取率(83.54%)和水溶性(32.27%)都明显高于普通淀粉型大麦Phenix(7.19%、74.95%和20.55%).两种麸皮经挤压
目的 研究酸雨对贫铀在土壤中迁移深度的影响及贫铀在我国6类代表土壤中的迁移规律,并探讨贫铀在土壤中迁移时对地下水的影响.方法 利用建立的贫铀在土壤中迁移的实验室模拟
The factors affecting the dimensional tolerance of powder injection molding (PIM), such as the selection of the powder and binder, the feedstock homogeneity, th