【摘 要】
：
Three-dimensional (3D) printing technology is becoming a promising method for fabricating highly complex ceramics owing to the arbitrary design and the infinite
【机 构】
：
School of Materials Science and Engineering,Key Laboratory of Advanced Ceramics and Machining Techno
论文部分内容阅读
Three-dimensional (3D) printing technology is becoming a promising method for fabricating highly complex ceramics owing to the arbitrary design and the infinite combination of materials. Insufficient density is one of the main problems with 3D printed ceramics, but concentrated descriptions of making dense ceramics are scarce. This review specifically introduces the principles of the four 3D printing technologies and focuses on the parameters of each technology that affect the densification of 3D printed ceramics, such as the performance of raw materials and the interaction between energy and materials. The technical challenges and suggestions about how to achieve higher ceramic density are presented subsequently. The goal of the presented work is to comprehend the roles of critical parameters in the subsequent 3D printing process to prepare dense ceramics that can meet the practical applications.
其他文献
依据工业机器人操作与运维“1+X”证书职业技能标准,以常见面盆水龙头的机器人打磨抛光为教学实施对象,对面盆水龙头生产流程和打磨工艺进行分析.阐述工业机器人操作与运维“
研究补强体系、生胶并用和硫化体系对充环烷油的溶聚丁苯橡胶(SSBR)胶料性能的影响。结果表明:对纯炭黑补强体系,炭黑用量为75份的胶料的综合性能较好,两种炭黑并用体系的胶料的综合性能提高,但耐磨性能稍差,对炭黑/白炭黑并用补强体系,白炭黑用量为20份的胶料的综合性能优异,继续增大白炭黑用量,填料分散性和胶料性能下降;SSBR并用20份顺丁橡胶,胶料的压缩生热和滚动阻力降低,耐磨性能提高,耐老化性能优异,其他性能满足使用要求;在硫化体系中硫黄用量对SSBR胶料性能的影响最大,硫黄的适宜用量为1.4~1.6份
以四氢糠醇(THFA)、氢氧化钠(NaOH)和氯代正己烷(NHC)为原料合成四氢糠醇己基醚(THE),并对其作为结构调节剂在阴离子聚合物合成中的应用进行研究。结果表明:在THFA/NaOH物质的量比为(2.5~3.0)/1、NaOH/NHC物质的量比为1/(1~1.05)、类似酯化的反应温度为125~140℃和反应时间为5~5.5 h、取代反应温度为20~40℃和反应时间为2 h的条件下,NHC转化率大于98%,THE收率大于95%,提纯后THE质量分数大于0.99;THE分别在溶聚丁苯橡胶、氢化苯乙烯-
在废旧橡胶的微波裂解腔体上设置4个波源和相应波导管,使用HFSS软件建立微波裂解模型,对裂解腔体上波导管馈口的分布方式和间距进行电场分布和微波能损耗分析.结果发现,微波
天然胶乳综合性能优异,应用模具拼装、凝固剂与硫化胶乳多次交替浸渍和干燥工艺,制作各种规格和结构复杂的气囊医用导管.介绍天然胶乳气囊导尿管、气囊前列腺医用导管、气囊
建立气相色谱-质谱联用快速测定玩具及儿童用品中苯并[c]芴、苯并[b]萘并[2,1-d]噻吩、5-甲基䓛和二苯并[cd,jk]芘4种多环芳烃的方法。结果表明,采用甲苯为萃取溶剂,超声波萃取50 min,采用DB-EUPAH毛细管色谱柱,选择离子监测模式下定量分析,可实现4种多环芳烃的有效分离。该方法的4种多环芳烃质量浓度测定线性范围为0.01~1 mg·L-1,线性相关因数不小于0.9992,加标回收率为86.5%~108.7%,相对标准偏差小于3%,可用于玩具及儿童用品中4种多环芳
介绍一带一路项目乌兹别克斯坦安格连橡胶厂建设的公用工程系统设计优化.为进一步控制成本、便于实施、使设备操作和维护更加便利,提出锅炉房除氧器溢流管增加水封、锅炉房凝
研究白炭黑、石蜡油、吸水树脂和吸水助剂ZA用量对三元乙丙橡胶吸水膨胀橡胶性能的影响.结果表明:在使用石蜡油改善胶料加工性能时,需要加入20份以上的白炭黑,否则硫化胶难以
In this work, three-dimensional (3D) Cf/SiBCN composites were fabricated by polymer infiltration and pyrolysis (PIP) with poly(methylvinyl)borosilazane as SiBCN
氟橡胶具有优异的耐化学腐蚀和耐高温性能,在航空航天、机械、石油、汽车和军工等领域广泛应用,减小氟橡胶摩擦因数和磨耗量不但能够延长其密封制品使用寿命,还能够提高生产