New acquisition decision algorithm for multiple access interference suppression in DSSS system

来源 :Journal of Systems Engineering and Electronics | 被引量 : 0次 | 上传用户:spaceturtle
下载到本地 , 更方便阅读
声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架
论文部分内容阅读
For decreasing the multiple access interference of weaker signal acquisition in direct sequence spread spectrum(DSSS) systems,a new single decision algorithm is presented.The maximum value of correlation results is conventionally detected.However,there may be not only one strong peak among correlation results when the cross-correlation noise is strong enough to affect the correlation results.The proposed algorithm decreases the false alarm probability through the decision of the ratio of the maximum value and the second maximum value of the correlation results.Theoretical analysis and simulation results indicate that the proposed algorithm effectively suppresses the acquisition problem of multiple access interference in DSSS system. For decreasing the multiple access interference of weaker signal acquisition in direct sequence spread spectrum (DSSS) systems, a new single decision algorithm is presented. The maximum value of correlation results is conventionally detected. However, there may be only only one strong peak among correlations results when the cross-correlation noise is strong enough to affect the correlation results. The proposed algorithm decreases the false alarm probability through the decision of the ratio of the maximum value and the second maximum value of the correlation results. that the proposed algorithm effectively suppresses the acquisition problem of multiple access interference in DSSS system.
其他文献
本文介绍我厂应用ABB机器人改造手动冲压线,并采用了目前先进的以太网和现场总线方式.提高劳动生产率,降低废品率.简单说明了自动线的结构,描述了控制系统的硬件组成和机器人
建立了连续拉索风雨激振的理论模型,采用有限差分法对拉索运动微分方程进行离散求解,并以南京长江二桥A20索为例进行分析.结果表明:风雨激振具有"限速"的特点;水线振动频率对
本文通过机器人在神龙公司冲压生产线的应用,介绍了机器人冲压生产线的构造及主要功能、特点,实践证明,机器人冲压生产线是今后的发展趋势。
本文介绍了一种将纸介质图纸经过一系列软硬件处理后而转换成由CAD系统可直接处理的电子图纸的方法--光栅矢量编辑.这种光栅矢量编辑的方法,简化了我们的设计过程,提高了设计
本文着重阐述了EQ1064左/右后侧围内板的拉延成形模拟过程,对其成形/变形特点作了介绍和分析,并运用板成形数值模拟这一新技术对拉延模进行了虚拟调试,和现场取得了基本一致
据西门子公司《元件通讯》1978年第6期报道,西德西门子公司慕尼黑热敏电阻研究发展部研制成功了一种1000℃高温负温度系数热敏电阻。这种热敏电阻的型号是H42,在相同的3×10
本文利用有限元软件ANSYS与LS-DYNA对典型实际冲压件成形过程进行了数值模拟,并取得成功.找出了工件开裂的原因,以及诸因素对成形结果的作用,改进了工艺.
本文简要阐述了窗框类冲压件的典型工艺过程,结合具体零件分析了在拉延过程中窗口反成形时工艺切口的布置及所起的作用,指出在修边后的整形工序中同样需要工艺切口并分析了原
本文介绍了激光加工技术在变型轿车大型三维覆盖件上的应用,解决了变型轿车生产中修边冲孔模具的大投入问题.
本文着重介绍如何控制红旗变型车车身制造过程中的变形.通过重新设计焊装台夹具的定位夹紧结构方案,经制造后投入使用保证了焊装后的车身达到一致性和白车身制造的质量.