【摘 要】
：
The strain rate sensitivity (SRS) and temperature sensitivity (TS) of 316L austenitic stainless steel were investigated by constant strain rate test (CSRT) and strain rate jump test (SRJT) under four temperatures (293,373,473 and 573 K) and four strain ra
【机 构】
：
School of Mechanical Engineering, Changzhou University,Changzhou 213164, China;Jiangsu Key Laborator
论文部分内容阅读
The strain rate sensitivity (SRS) and temperature sensitivity (TS) of 316L austenitic stainless steel were investigated by constant strain rate test (CSRT) and strain rate jump test (SRJT) under four temperatures (293,373,473 and 573 K) and four strain rates (5 × 10-4/s,1 × 10-3/s,5 × 10-3/s and 1 × 10-2/s).The results show that temperature sensitivity (TS) indexes at different strain rates are coincidence to be negative,related to temperature softening.On the contrary,SRS indexes change from positive to negative with the increase in temperature associated with dynamic strain aging (DSA).Moreover,based on the comparison between CSRT and SRJT,SRS and TS indexes obtained by two methods agree well.It proves that the SRJT can describe the SRS and TS phenomenon of 316L efficiently.Furthermore,the effects of temperature and strain rate on fracture mechanism were discussed.At last,an improved Johnson-Cook model was proposed to consider the temperature-dependent SRS behavior of 316L.
其他文献
The 7th China-Japan Bilateral Symposium on High Temperature Strength of Materials was held at Dalian, China, during the period August 23-27, 2010.The symposium was co-organized by the High Temperature Strength and Materials Committee, the Society of Mater
Susceptibility and morphological characteristics of crevice corrosion for SS316,SS904L,SS254sMo and SS2507 in the simulated low-temperature multi-effect distillation environment were investigated by cyclic polarization test,scanning electron microscope an
In this work,the GaN thin films were directly deposited on multilayer graphene (MLG) by plasma-enhanced atomic layer deposition.The deposition was carried out at a low temperature using triethylgallium (TEGa) precursor and Ar/N2/H2 plasma.Chemical propert
Microstructure and mechanical properties of Ni-28W-6Cr alloy-welded joints produced by gas tungsten arc welding were investigated in this work.Results showed that original fine-grain base metal near fusion line totally transformed into coarse heat affecte
Immiscible alloys have aroused considerable interests in the last decades on account of their special physical and mechanical properties and potential applications.A considerable number of researches have been implemented to investigate the solidification
Hot deformation behavior of a high Al-low Si transformation-induced plasticity (TRIP) steel was studied by an MMS-300 thermo-simulation machine at the temperature range of 1050-1200 ℃ and strain rate range of 0.01-10 s-1.The constitutive equations of the
In a fusion reactor,plasma-facing components (PFCs) will suffer severe thermal shock;behavior and performance of PFCs under high heat flux (HHF) loads are of major importance for the long-term stable operation of the reactor.This work investigates the the
The composition and structural evolution of the corrosion product film of two commercial 90Cu-10Ni tubes,namely Tube A and Tube B,after being immersed in natural seawater for 1,3,and 6 months were characterized by scanning electron microscopy,energy-dispe
The effect of thermal aging on phase transformation and impact toughness of an as-cast duplex stainless steel was investigated at room temperature.After long-term thermal aging,the impact toughness decreases significantly and the cracks initiate and propa
The fracture of pipelines caused by corrosion cracks and the resulting oil and gas leakage can lead to great environmental pollution and economic losses.These negative effects are due to serious corrosion of the plain carbon steels used for armor of flexi