Effect of Short-Time Aging on the Pitting Corrosion Behavior of a Novel Lean Duplex Stainless Steel

来源 :金属学报(英文版) | 被引量 : 0次 | 上传用户:zhengyicai2010
下载到本地 , 更方便阅读
声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架
论文部分内容阅读
The effect of short-time aging in the temperature range between 400 and 1000 ℃ on the pitting corrosion behavior and mechanical property of a novel lean duplex stainless steel (LDSS) 2002 was investigated through the potentiostatic critical pitting temperature (CPT) tests and the Charpy impact tests.Both the pitting corrosion resistance and the toughness of aged specimens degraded due to the precipitation of detrimental secondary phases and the most significant reduction of CPT and impact energy emerged at 650 ℃ concurrently.The CPT of LDSS 2002 specimen aged at 650 ℃ decreased by 28 ℃,and the impact energy dropped from 69 to 29 J/cm2 compared with the solution-annealed sample.Transmission electron microscopy characterization showed that the main precipitates in LDSS 2002 were Cr2N and M23C6 along the ferriteaustenite grain boundaries.
其他文献
The microstructure,electrical conductivity and electromagnetic interference shielding effectiveness of Mg-X (X=Al,Sn,Y and Gd) alloys in as-cast and solution states were systematically investigated in this study.The electrical conductivity and electromagn
The thermal stability and mechanical properties of China low activation martensitic steel with Zr and Y were investigated via thermal aging at 550 ℃ for 8000 h.The Laves phase content monotonically increased with thermal aging,and the volume fraction of t
The hot deformation behavior and workability of a new reduced activation ferritic/martensitic steel named SIMP steel for accelerator-driven system were studied.The flow curve and its microstructure were studied at 900-1200 ℃ and strain rate range of 0.001
Carbon nanofiber (CNF)-reinforced aluminum-matrix composites were fabricated via ball milling and spark plasma sintering (SPS),SPS followed by hot extrusion and powder extrusion.Two mixing conditions of CNF and aluminum powder were adopted:milling at 90 r
The corrosion behavior of stainless steel exposed to a simulated salt lake atmosphere has been investigated by analyzing the evolution of surface morphologies and corrosion products,the initiation and development of pits,and the electrochemical characteri
In this study,the effect of cooling rates on microstructures and mechanical properties in a Al-bearing hot-rolled transformation-induced plasticity steel was investigated.The experiments were carried out using hot simulation machine and hot rolling mill,w
The influence of processing temperature on grain size reduction in AA 6063 aluminum alloy subjected to repetitive corrugation and straightening (RCS) is investigated in this work.The aluminum alloy was processed by RCS at different temperatures (room temp
In this study,powder mixtures containing (Ti,W)C additions (10,20,30 and 40 wt%) were prepared and then consolidated at 1200,1250,1300 and 1350 ℃ by spark plasma sintering.The effect of (Ti,W)C additions on the microstructure and mechanical properties of
The effect of pH on the electrochemical behaviour and passive film composition of 316L stainless steel in alkaline solutions was studied using electrochemical measurements and a surface analysis method.The critical pH of 12.5 was found for the conversion
A CoCrFeMnNi high-entropy alloy with a high content of carbon was synthesized,and its hot deformation behavior was studied at the temperatures 800-1000 ℃ at the strain rates ranging from 0.001 to 0.1 s-1.As-prepared alloy is a face-centered cubic-structur