【摘 要】
：
Fabrication of the surface micro-texture on the C-plane sapphire is undertaken by a 355 nm Ultraviolet (UV) pulsed laser.The surface micro-textures of sapphire with different laser scanning line spacing ranging from 10 μm to 100 μm are obtained,where the
【机 构】
：
College of Mechanical and Electrical Engineering,Nanjing University of Aeronautics and Astronautics,
论文部分内容阅读
Fabrication of the surface micro-texture on the C-plane sapphire is undertaken by a 355 nm Ultraviolet (UV) pulsed laser.The surface micro-textures of sapphire with different laser scanning line spacing ranging from 10 μm to 100 μm are obtained,where the selection range of scanning line spacing is controlled in the range of the groove width and plasma width to obtain a surface of high Peak-Valley (PV) value.A reasonable processing order is proposed to manufacture different types of surface micro-textures on sapphire by laser ablation trajectory regulation.In the multiple-passes laser ablation of sapphire by the UV nanosecond pulsed laser,the scanning lines in each direction is treated as once scanning.On this basis,the multiple processing can be carried out to avoid the influence of the subsequent scanning on the machined groove.In addition,the effect of different scanning line spacing on the PV value is quantified and different types of surface micro-textures on sapphire,including the squares,the rhombuses and the hexagons,are successfully fab-ricated,which can be applied in the friction reduction or anti-reflection field.
其他文献
Airborne Distributed Coherent Aperture Radar (ADCAR) is one of the most promising next-generation radars to significantly improve target detection and discrimination abilities.How-ever,time and phase synchronization among unit radars should be done before
Underwater navigation system is an indispensable part for autonomous underwater vehicles.Due to the indiscernibility of satellite signal,however,the underwater navigation problem is quite challenging,and a satellite-free navigation scheme should be looked
This paper investigates the problem of a 2-D plate containing internal cracks at arbitrary angles to the heating surface under thermal shock.The finite difference method is applied to solve the temperature distribution and a difference scheme of the obliq
为确保吴家园水库的运行安全,充分发挥吴家园水库的综合效益,文章阐述了如何科学编制大中型水库兴利控制运用计划,结合吴家园水库水雨情实际,编制水库汛期调度运用计划,充分发挥水库的兴利功能,最大限度地利用水资源.
文章对北方地区输水隧洞冬季施工喷射混凝土速凝剂进行性能指标试验.试验结果表明:无碱液体速凝剂对于北方地区输水隧洞冬季施工喷射混凝的速凝效果最佳,工程施工时速凝剂的初凝时间尽量控制在3-5 min较为适宜.研究成果对于北方寒区输水隧洞施工速凝剂的选择及主要性能指标选择具有重要参考价值.
The radial ultrasonic rolling electrochemical micromachining (RUR-EMM) combined rolling electrochemical micromachining (R-EMM) and ultrasonic vibration was studied in this paper.The fundamental understanding of the machining process especially the interac
Precision and low damage grinding of aviation optical elements can effectively improve the overall processing efficiency.The mechanism of high-speed cross scuffing of multiple abrasive particles has become an important factor affecting the forming quality
The tracking control problem for Flexible Joint Manipulator Control System (FJMCS)with unmeasurable states is addressed in this paper.Firstly,a High-Gain Observer (HGO) is con-structed to estimate the unmeasurable states and the uncertainties.Then,a Dynam
清原镇段河道两岸均为自然萌生柳树丛林,抵御洪水冲刷能力较强,但防洪标准不高,当年洪水很大,两岸漫流致使全镇受灾,该镇的大面积居民楼倒塌,城市东部粮库旧址的化工厂部分也被洪水淹没.洪水淹没的农田减产,经济损失惨重,鉴于此文章对清原县城的干支流洪水进行了分析,同时对治理后设计洪水进行了计算,经治理后确保当地农田灌溉及人民生命得到保障.
文章采用水热化估算方法对北方地区冬季水工混凝土施工的热能损耗率进行试验.试验分析表明:冬季水工混凝土热能损耗的主因在于其内壁厚度,热能损耗率可通过增加其内壁厚度来有效降低,从而增强冬季水工混凝土施工结构的稳定程度.研究成果对于北方地区冬季水利工程施工设计具有重要参考价值.