Corrosion Resistance and Electrochemical Behaviour of Amorphous Ni84.9Cr7.4Si4.2Fe3.5 Alloy in Alkal

来源 :金属学报(英文版) | 被引量 : 0次 | 上传用户:snowliya
下载到本地 , 更方便阅读
声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架
论文部分内容阅读
In this work,the corrosion behaviours of the amorphous Ni84.9Cr7.4Si4.2Fe3.5 alloy and its crystalline counterpart are studied in acidic,neutral,and alkaline solutions by scanning electron microscopy,electrochemical impedance spectroscopy,and potentiodynamic and potentiostatic polarization tests· X-ray photoelectron spectroscopy and scanning Kelvin probe are employed to characterize the alloy surface· The results show that the amorphous Ni84.9Cr7.4Si4.2Fe3.5 alloy presents a better corrosion resistance compared to its crystalline counterpart,which is attributed to the uniform energy distribution of the atoms on the amorphous alloy surface,and this presents as a uniform electric potential map to effectively suppress the occurrence of the corrosion cell reaction.
其他文献
Glass fibres/epoxy resins composites have been performed as ideal materials to make support instruments for high-energy and nuclear physics experiments.The effects of the γ-ray irradiation on the fatigue strength,thermal conductivities and thermal stabili
Boron-doped aluminum nitride (B-A1N) thin films were synthesized on A1 substrates by using chemical vapor deposition method by changing the synthesis parameters and were used as thermal interface material for high power light emitting diode (LED).The B-A1
Solidification shrinkage has been recognized as an important factor for macrosegregation formation.An arbitrary Lagrangian-Eulerian (ALE) model is constructed to predict the macrosegregation caused by thermal-solutal convection and solidification shrinkag
Mixtures of W and B13C2 powders were mechanically milled and subsequently annealed at 900-1200℃.It is found that amorphous W-B-C alloy formed as the mixtures were milled for 20-80 h.After annealing the 80 h-milled mixtures at 900-950 ℃,solid solutions of
Target assembly is a key consumable material for producing thin film used in the electronic packaging and devices.The residual stresses induced during the process of soldering are detrimental to the performance of target assembly.In this work,the intensit
Mg-Zn-Ag alloys have been extensively studied in recent years for potential biodegradable implants due to their unique mechanical properties, biodegradability and biocompatibility. In the present study, Mg-3Zn-xAg (wt%, x = 0. 2, 0. 5 and 0. 8) alloys wit
Both of the single crystal (SX) castability and undercoolability of PWA 1383 superalloy were investigated during the directional solidification and isothermal cooling.In all the six SX parts of a casting cluster,no stray grains were found,revealing a defe
The effect of sulphide (Na2S) concentration (SC) on the corrosion and cavitation erosion behaviours of a cast nickel aluminium bronze (NAB) in 3.5% NaC1 solution is investigated in this study.The results show that when the SC exceeds 50 ppm,the hydrogen e
Diffusion bonding of refractory Nb-Si-based alloy was performed with Ni/Al and Ti/Al nanolayers under the condition of 1473 K/30 MPa/60 min.The NbSS/Nb5Si3 in situ composite with the nominal composition of Nb-22Ti-16Si-3Cr-3Al-2Hf was used as the parent m
The hot deformation behavior of Fe-26Mn-6.2Al-0.05C steel was studied by experimental hot compression tests in the temperature range of 800-1050 ℃ and strain rate range of 0.01-30 s-1 on a Gleeble-3500 thermal simulation machine.The microstructural evolut