New Gasoline Passenger Car Engine Oil Performance Category

来源 :润滑油 | 被引量 : 0次 | 上传用户:A578964735
下载到本地 , 更方便阅读
声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架
论文部分内容阅读
This paper primarily focuses on the development of the International Lubricant Standardization & Approval Committee (ILSAC) GF-5 passenger car engine oil category in North America and Japan including key technical performance requirements. New ILSAC GF-5 is scheduled to be introduced during the 3rd quarter of 2010 and will supersede ILSAC GF-4 and previous categories. It will also be backward compatible and will provide improved performance relative to GF-4 in many respects. At the same time, when GF-5 is introduced, it is anticipated that API SN will also be introduced as a new performance category to supersede the current category, API SM. This paper was focused on the development of the International Lubricant Standardization & Approval Committee (ILSAC) GF-5 passenger car engine oil category in North America and Japan including key technical performance requirements. New ILSAC GF-5 is scheduled to be introduced during the 3rd quarter of 2010 and will supersede ILSAC GF-4 and previous categories. It will also be backward compatible and will provide improved performance relative to GF-4 in many respects. At the same time, when GF-5 is introduced, it is anticipate that API SN will also be introduced as a new performance category to supersede the current category, API SM.
其他文献
在试验基础上,分析了不锈钢与石墨接触电阻在不同热处理温度下随热处理时间的变化关系,并建立了质子交换膜燃料电池热处理不锈钢双极板的热机械模型.结果表明:在同一温度下,
目的 比较针刺手三阴经穴与手阳明经穴改善脑卒中软瘫期手指屈伸功能障碍的临床疗效.方法 将患者随机分为两组,阳明组45例给予针刺手阳明经诸穴,三阴组44例给予针刺手三阴经
通过化学镀的方法制得Ni-P-Al2O3镀层,利用扫描电镜、能谱仪、X射线衍射及硬度计对镀层的形貌、组织结构和硬度进行分析。结果表明:镀层中所含主要元素为Ni、P和Al。镀层界面
对17-4PH不锈钢进行表面激光淬火,分析了激光淬火后的组织、硬度、残余应力和疲劳寿命。结果表明:激光淬火后,17-4PH不锈钢组织分为淬硬区、过渡区和基体,淬硬层深1.2mm,平均
为评价满足OEM新产品使用要求润滑油的性能,中国石油大连润滑油研究开发中心与道依茨一汽(大连)柴油机有限公司在大连润滑油研究开发中心联合建立了DEUTZ1013FC柴油机台架.该
研究了825合金热挤压管中碳化物的时效析出及回溶行为。结果表明,在750~800℃时效时,沿晶界会大量析出M23C6型碳化物,造成晶界附近Cr元素贫化,从而显著降低该合金的抗晶间腐蚀
对低碳钢渗碳处理后进行不同的热处理和深冷处理,检测了试件的扭转强度。结果表明:影响扭转强度的因素主次顺序依次为深冷处理时间、淬火温度、回火温度和回火保温时间;最优
选用几种不同成分的CuAlBe合金,测试了合金在不同热处理状态下的形状记忆效应。结果表明:CuAlBe合金具有较好的形状记忆性能。近共析成分合金记忆性能优于其他合金;正火状态