【摘 要】
：
Current modules and systems lose a significant part of their power when shade is present.A solution is presented by adapting the electrical lay-out of the module, without additional manufacturing cost
【机 构】
：
ECN Solar Energy, The Netherlands Eurotron, The N
【出 处】
：
SNEC 第九届(2015)国际太阳能产业及光伏工程(上海)论坛
论文部分内容阅读
Current modules and systems lose a significant part of their power when shade is present.A solution is presented by adapting the electrical lay-out of the module, without additional manufacturing costs.Such a module has several advantages: the annual yield is significantly higher when shade is present, no shade analysis needs to be carried out by the installer, the temperature rise resulting from diodes is strongly reduced as is the risk of damage due to hotspots, combined with a dedicated micro-inverter this leads to an easy to install plug-and-play system.It allows utilization of an entire roof area, and hence improves aesthetics and the market for PV.
其他文献
温度对晶硅太阳电池组件有着重要的影响.太阳电池组件温度较高时，工作效率下降.随着太阳能电池温度的增加，开路电压减小，在20 ～ 100℃范围，大约每升高1℃每片电池的电压减小2mV；而光电流随温度的增加略有上升，大约每升高1℃每片电池的光电流增加千分之一，或0.03mA/℃·cm2.
在常规多晶扩散生产中，大多使用瓶装三氯氧磷间歇生产。随着生产的进行，三氯氧磷逐渐消耗，源瓶内液面下降，造成瓶内三氯氧磷饱和蒸汽压逐渐下降。在保持通八氮气总量不变情况下，气体携带的三氯氧磷分子逐渐减少，导致扩散后方阻变大，均匀性变差。
We report on our latest results on high efficiency n-type metal-wrap-through (MWT) cell and module technology.The bifacial n-type MWT cells are produced using industrial processes in industrial full-s
Mono-like crystalline silicon ingot with high purity was continuously casted with metallurgical-grade silicon (MG-Si) as feedstock.Our advanced electron beam melting (EBM) system is able to effectivel
Solar simulators copy the AM1.5 spectrum for an accurate efficiency measurement of solar cells.Encapsulation of solar cells with EVA and glass modify the AM1.5 spectrum inside the module.Less UV light
本文对定向凝固(DSS)法生长的P型掺硼多晶硅材料的太阳电池片的关照衰减问题，采用不同的光致衰减方法，对太阳能电池片电性能的影响进行了简单的对比研究，可以再次验证其中一种方法在行业中的普遍应用，可以通过比较两种衰减方法，保证太阳能电池片输出电性能的稳定、准确与可靠性，给使用单位建议可行的衰减方式。
With increased market demand for distributed solar array systems, module makers and installers are looking forward to the solutions of easy installation and cost effective.Based on DuPont performance
Bifacial photovoltaic devices, thanks to their proven benefits and the maturity of the production processes, can make a breakthrough in the photovoltaic market.However, the current lack of standardize
Some advanced crystalline silicon solar cells and modules technologies present evolutions of their backside metallisation.This results in new needs in terms of non-permanent contacting for characteriz
The thermal laser separation (TLS) allows the ablation free cleaving to separate solar cells with a high edge quality.The process is based on thermal induced mechanical stress, generated by a well-adj