CORRELATION FACTOR STUDY OF SMALL PUNCH CREEP TEST AND ITS LIFE PREDICTION

来源 :第四届微试样测试技术国际学术会议((The 4th International Conference on Small | 被引量 : 0次 | 上传用户：lumuming

【摘要】

：

Small punch test is one of the innovative methods that can be used to evaluate the properties of material without destructive harm to the in-service component.

【作者】

：

Cheng Wen Tong Xu Kaishu Guan

【机构】

：

Scholl of mechanical and power engineering,East China University of Science and Technology,No.130 Me

【出处】

：

第四届微试样测试技术国际学术会议((The 4th International Conference on Small

【发表日期】

：

2016年4期

【关键词】

：

Small Punch Creep Test Uniaxial Creep Test Correlation Factor Life Prediction

下载到本地 , 更方便阅读

下载此文赞助VIP

声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架

论文部分内容阅读

　　Small punch test is one of the innovative methods that can be used to evaluate the properties of material without destructive harm to the in-service component.

其他文献

DEVELOPMENT OF FATIGUE TESTING MACHINE FORSMALL SIZED SPECIEN IN LIQUID CONDITION

This paper describes the development of fatigue testing machine for small sized test specimens in liquid conditions.This type of fatigue testing machine is not available commercially so the testing ma

会议

FatigueFatigue testing machineSmall sized specimenLiquid conditions

RESEARCH ON FATIGUE PROPERTIES OF MICRON SCALE COPPER BONDING WIRES

The symmetrical bending fatigue behavior of micron scale copper bonding wires with different diameter was examined by using a new device for microcantilevers based on self-excited vibration principle.

会议

Micron copper wireFatigueSize effect

LOW CYCLE FATIGUE AND CREEP-FATIGUE OF LEAD FREE SOLDERS TESTED BY SMALL SIZED SPECIMEN

Solder alloys are widely used as connecting materials in electronic devices.Currently,lead free solders are used for soldering because of RoHS directive that restricted the use of certain hazardous su

会议

STRAIN CORRECTION IN SMALL SPECIMEN TENSILE TEST WITHOUT EXTENSOMETER

Small specimen is widely used in mechanical test of reactor structural materials due to the limited volume in irradiation facility and less activity after irradiated.

会议

AN ALTERNATIVE METHOD FOR STRAIN-CONTROLLED FATIGUE TEST AT ELEVATED TEMPERATURE

For strain-controlled fatigue tests,especially at elevated temperature,implementation of knife-edges and punching dimples within gauge length of specimen may cause premature failure on the test sectio

会议

EVALUATION OF CREEP DEFORMATION BY INDENTATION TEST WITH A CONSTANT DEPTH-APPLICABILITY FOR INHOMOGE

Toevaluate the strength reliability of the electronic substrate,it is requiredto obtain the creep properties of the solder joint in-situ.The indentation test is one of effective method to evaluate the

会议

DETERMINATION OF CREEP DAMAGE PROPERTIES FROM A MINIATURE THREE POINT BENDING SPECIMEN USING AN INVE

In this work,a novel method for determining the creep damage properties which can be used to represent the full life until failure from a miniature bending creep test specimen is developed based on a

会议

Creep damage propertiesminiature specimenthree-point bendinginverse approach

IMPROVEMENT OF PREDICTING MECHANICAL PROPERTIES FROM SPHERICAL INDENTATION TEST

Although nowadays the Instrumented Indentation Test(IIT)can be applied to the fields from nano-micro-to macroscopic scale,this paper only addresses its application in the area of life assessment of co

会议

STUDY OF FATIGUE PROPERTIES OF MATERIALS THROUGH BALL INDENTATION AND SMALL PUNCH TEST METHODS

Fatigue property of materials is an important input while estimating the residual life of critical components,as,fatigue data(stress vs.cycles or strain vs.cycles or fatigue crack growth rate data)are

会议

VERIFICATION AND CALIBRATION OF INSTRUMENTED INDENTATION TESTING MACHINES

The frame compliance is calibrated by experimental and calculation methods for an instrumented equipment.The indentation depth and diameter with single cycle test is determined by confocal laser scann

会议

CORRELATION FACTOR STUDY OF SMALL PUNCH CREEP TEST AND ITS LIFE PREDICTION

与本文相关的学术论文