【摘 要】
：
With modern steel manufacture capacity increasing,the demand for techniques of quick and accurate inclusion evaluation of the slab by large scale becomes urgent for the metallurgical technicians,espec
【机 构】
：
R&D Center of Baosteel company,No.655,Fujin Road,Baoshan District,Shanghai 201900,China
【出 处】
：
第十届中国钢铁年会暨第六届宝钢学术年会
论文部分内容阅读
With modern steel manufacture capacity increasing,the demand for techniques of quick and accurate inclusion evaluation of the slab by large scale becomes urgent for the metallurgical technicians,especially the test carried out on the initial steel products.By these test results,the quality of further processed steel product can be forecasted.These techniques involve the investigation on inclusions size,distribution,kind,and quantity.At present,the ultrasonic method is a suitable means to meet this demand.In this paper,inclusions detection sensitivity by focused ultrasonic method on the slab specimen is discussed,and an ultrasonic method by which inclusion as small as 100μm in the slab specimen of 30mm thick can be efficiently tested is proposed by the help of the focused ultrasonic transducer whose working frequency is 7.5MHz.The test result is verified by mechanical dissection and microscope observation at last,the experiment result demonstrates that not only it is feasible to carry out inclusion detection directly on the slab specimen by ultrasonic method,but also the ultrasonic detection sensitivity can be much higher than commonly estimated degree.
其他文献
Gontermann-Peipers GmbH(GP)Germany developed a new,high alloyed steel grade(Hot working steel)for the manufacturing of back-up rolls in Skin Pass Mills.The advanced GP double pour casting processes pr
本文在凝固压力为0.5MPa、0.85MPa、1.2MPa的条件下,利用25kg加压感应炉,在尺寸不同的铸型中,制备出了高氮奥氏体不锈钢P2000(氮含量约0.9％),并结合Thermo-Calc热力计算软件和低倍组织检测手段,研究了压力对高氮不锈钢宏观组织的影响规律;结果表明,增大压力和冷却速率能够有效避免铸锭内气孔的形成,加压可增强液相的补缩能力,明显减少中心疏松深度和面积,提高铸锭致密度,此
回顾了首钢总公司迁顺产线、京唐产线、首秦产线近五年来的炼钢技术创新进展.在过去的五年以来,优化了KR铁水脱硫的生产工艺参数,理顺了“KR+转炉+RH+连铸”流程生产低硫钢种([％S]≤0.0030)工艺;围绕转炉“全三脱”的特点进行高效低成本脱磷、控制增氮的工艺研究;开发了SGRS工艺,转炉炼钢石灰、轻烧白云石消耗降低30％以上;针对不同钢种的使用要求,采用相应的措施,使钢中的非金属夹杂物得到良好
随着钢铁工业节能减排的深入,烧结过程中低温余热资源的回收技术成为研究的热点.针对钢铁工业中烧结矿冷却和显热提取及再利用过程,依据热力学第一定律和第二定律,在冷却机、余热锅炉和汽轮发电机组耦合响应机制的基础上,建立余热资源回收率和吨矿余热发电量模型,选定三个工况计算了吨矿极限发电量和理论发电量,分析了影响烧结余热发电负荷的因素,给出了烧结余热发电负荷提升的方法,并基于场协同原理及梯级利用原则提出了烧
Non-blast-furnace ironmaking,or non-coking ironmaking,is one of the most concerned focuses in iron and steel industry,particularly in China.Although it covers a great number of various processes for b
Ferritic stainless steel is being paid attention by steel industry and downstream users relying on its good over-all properties and low cost.With improvement of metallurgical technology and researchin
钢铁工业是能源密集型的行业，消耗大量化石能源，排放大量CO2.中国作为世界第一钢铁产量的大国，钢铁工业CO2 排放约占全国总排放的15％，同时炼钢过程中排放大量的污水.在世界性 CO2 减排和环境保护的压力下，欧盟、日本、韩国等主要钢铁生产地区均制定了相应的规划和技术措施，中国的钢铁行业CO2 排放量现在仍维持在相对较高的水平，随着环境要求的日趋严格，有效减少钢铁生产 CO2 和污水排放已成为中国
A compact Zn-Al coating was successfully deposited by cold spraying technique.The effect of annealing temperature on the microstructure,microhardness and wear properties of the coatings was explored.T
The steel and metallurgical developments to support lightweighting,performance improvements and improved line efficiencies for the can-making and packaging industries in general are discussed.The pape
During the pre-and middle periods of one whole BOF campaign in 300 t converters at Baosteel,bottom tuyeres status is good so that the effect of combined blowing is more obvious.But during the later pe